Új hozzászólás Aktív témák

• #19238 yodee_ őstag tlac #19173

  Új Válasz 2024-01-02 16:03:03 #19238

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  yodee_

  őstag

  válasz tlac #19173 üzenetére

  Sziasztok!

  Korábban Én is szemeztem a fancontrol -lal, mivel ubuntu alatt nagy megelégedettséggel használom. A leírás alapján minden megcsinálok, telepítek minden függőséget. Lefut a pwmconfig és létrejön a fancontrol konfiguráció.

  root@OpenWRT_x86-64:/etc/fan$ ./pwmconfig
# pwmconfig version 3.6.0
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.
We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.
Found the following devices:
   hwmon0 is acpitz
   hwmon1 is coretemp
   hwmon2 is w83627dhg
Found the following PWM controls:
   hwmon2/pwm1           current value: 255
   hwmon2/pwm2           current value: 255
   hwmon2/pwm3           current value: 255
   hwmon2/pwm4           current value: 255
Giving the fans some time to reach full speed...
Found the following fan sensors:
   hwmon2/fan1_input     current speed: 1917 RPM
   hwmon2/fan2_input     current speed: 6026 RPM
   hwmon2/fan3_input     current speed: 0 ... skipping!
   hwmon2/fan4_input     current speed: 0 ... skipping!
   hwmon2/fan5_input     current speed: 0 ... skipping!
Warning!!! This program will stop your fans, one at a time,
for approximately 5 seconds each!!!
This may cause your processor temperature to rise!!!
If you do not want to do this hit control-C now!!!
Hit return to continue:
Testing pwm control hwmon2/pwm1 ...
  hwmon2/fan1_input ... speed was 1917 now 1917
    no correlation
  hwmon2/fan2_input ... speed was 6026 now 6026
    no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon2/pwm1,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)? n
Testing pwm control hwmon2/pwm2 ...
  hwmon2/fan1_input ... speed was 1917 now 1896
    no correlation
  hwmon2/fan2_input ... speed was 6026 now 6026
    no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon2/pwm2,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)? n
Testing pwm control hwmon2/pwm3 ...
  hwmon2/fan1_input ... speed was 1917 now 1906
    no correlation
  hwmon2/fan2_input ... speed was 6026 now 0
    It appears that fan hwmon2/fan2_input
    is controlled by pwm hwmon2/pwm3
Would you like to generate a detailed correlation (y)? n
Testing pwm control hwmon2/pwm4 ...
  hwmon2/fan1_input ... speed was 1917 now 1917
    no correlation
  hwmon2/fan2_input ... speed was 6026 now 6026
    no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon2/pwm4,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)? n
Testing is complete.
Please verify that all fans have returned to their normal speed.
The fancontrol script can automatically respond to temperature changes
of your system by changing fanspeeds.
Do you want to set up its configuration file now (y)? y
What should be the path to your fancontrol config file (/etc/fancontrol)? /etc/fan/fancontrol
Loading configuration from /etc/fan/fancontrol ...
Select fan output to configure, or other action:
1) hwmon2/pwm3         4) Save and quit
2) Change INTERVAL     5) Show configuration
3) Just quit
select (1-n): 1
Devices:
hwmon0 is acpitz
hwmon1 is coretemp
hwmon2 is w83627dhg
Current temperature readings are as follows:
hwmon0/temp1_input      27
hwmon0/temp2_input      29
hwmon1/temp1_input      29
hwmon1/temp2_input      27
hwmon1/temp3_input      28
hwmon1/temp4_input      24
hwmon1/temp5_input      28
hwmon2/temp1_input      26
hwmon2/temp2_input      0
hwmon2/temp3_input      23
Select a temperature sensor as source for hwmon2/pwm3:
 1) hwmon0/temp1_input
 2) hwmon0/temp2_input
 3) hwmon1/temp1_input
 4) hwmon1/temp2_input
 5) hwmon1/temp3_input
 6) hwmon1/temp4_input
 7) hwmon1/temp5_input
 8) hwmon2/temp1_input
 9) hwmon2/temp2_input
10) hwmon2/temp3_input
11) None (Do not affect this PWM output)
select (1-n): 8
Enter the low temperature (degree C)
below which the fan should spin at minimum speed (20): 30
Enter the high temperature (degree C)
over which the fan should spin at maximum speed (60): 55
Enter the minimum PWM value (0-255)
at which the fan STOPS spinning (press t to test) (100): 100
Enter the minimum PWM value (100-255)
at which the fan STARTS spinning (press t to test) (150): 110
Enter the PWM value (0-100) to use when the temperature
is below the low temperature limit (0): 0
Enter the PWM value (100-255) to use when the temperature
is over the high temperature limit (255): 255
Select fan output to configure, or other action:
1) hwmon2/pwm3         4) Save and quit
2) Change INTERVAL     5) Show configuration
3) Just quit
select (1-n): 5
Common Settings:
INTERVAL=10
Settings of hwmon2/pwm3:
  Depends on hwmon2/temp1_input
  Controls hwmon2/fan2_input
  MINTEMP=30
  MAXTEMP=55
  MINSTART=110
  MINSTOP=100
  MINPWM=0
  MAXPWM=255
Select fan output to configure, or other action:
1) hwmon2/pwm3         4) Save and quit
2) Change INTERVAL     5) Show configuration
3) Just quit
select (1-n): 4
Saving configuration to /etc/fan/fancontrol...
Configuration saved

  Érdekesség, hogy a pwmconfig lefuttatása előtt a fancontrol egy futtatható állomány, utána nekem kell azzá tennem. Amint ezt megteszem, és próbálom futtatni ezt kapom:

  root@OpenWRT_x86-64:/etc/fan# ./fancontrol &
root@OpenWRT_x86-64:/etc/fan# ./fancontrol: line 5: hwmon2/pwm3=hwmon2/temp1_input: not found
./fancontrol: line 6: hwmon2/pwm3=hwmon2/fan2_input: not found
./fancontrol: line 7: hwmon2/pwm3=30: not found
./fancontrol: line 8: hwmon2/pwm3=55: not found
./fancontrol: line 9: hwmon2/pwm3=110: not found
./fancontrol: line 10: hwmon2/pwm3=100: not found
./fancontrol: line 11: hwmon2/pwm3=0: not found
./fancontrol: line 12: hwmon2/pwm3=255: not found
[1]+  Done(127)                  ./fancontrol

  Nem tudom merre induljak el. Mi lehet a gond?

Új hozzászólás Aktív témák